任何机械设备都有自己的正常磨损和工作极限，在设备给我们创造利润的时候我们也不能忘记他们也需要“呵护”哦，下面简单介绍下中空玻璃设备的保养及维护注意事项。
Any mechanical equipment has its own normal wear and working limit. When the equipment creates profits for us, we should not forget that they also need "care". Here is a brief introduction to the maintenance and precautions of insulating glass equipment.
操作注意事项：
Precautions for operation:
1 转动皮带传送开关，使其处于“开”位置，观察皮带是否有跑偏现象，并调整涨紧螺栓，使其校正。
1 Turn the belt conveyor switch to the "on" position, observe whether the belt deviates, and adjust the tightening bolt to make it correct.
2 开机前，依据间隔框宽度，松开打胶头紧定螺栓，调整两挤胶头的间隔距离，调整时，要使框的对称中心、两个小压轮宽度的对称中心、两打胶头的对称中心重合（此项只有在间隔框宽度改变时进行调整），调整完毕紧固螺钉。
2 Before starting the machine, loosen the fastening bolts of the rubber head according to the width of the spacing frame, and adjust the spacing distance between the two extrusion heads. During the adjustment, make the symmetrical center of the frame, the symmetrical center of the width of the two small pressing wheels, and the symmetrical center of the two rubber heads coincide (this item can only be adjusted when the width of the spacing frame changes). After the adjustment, tighten the screws.
3 工作前温度调节： 因各厂家生产丁基胶规定的加热温度及工艺参数不同，所以设定打胶座温度一般为120－140度，胶缸温度为110－120度（此值仅作参考），待加热温度达到设定值15－30分钟后，方可打胶。
3 Temperature regulation before operation: Because the heating temperature and process parameters specified for butyl rubber produced by various manufacturers are different, the set temperature of the glue injection base is generally 120-140 degrees, and the temperature of the glue cylinder is 110-120 degrees (this value is only for reference). The glue can be applied only after the heating temperature reaches the set value for 15-30 minutes.
4 在液压缸挤胶活塞工作终点和每次工作完毕，应将液压压力降为零：且胶未加指定温度前，挤胶活塞不要推进或离开。否则，将产生机械损坏。
4 The hydraulic pressure shall be reduced to zero when the rubber extrusion piston of the hydraulic cylinder works to the end point and every time the work is completed; the rubber extrusion piston shall not be pushed or left before the rubber is added to the specified temperature. Otherwise, mechanical damage will occur.

5 检查气源，应保证使用经干燥的洁净空气，并定期排放滤清器的积水，检查油雾器中的油是否够用。
5 To check the air source, firstly ensure that the dry clean air is used, regularly drain the water in the filter, and check whether the oil in the oil atomizer is sufficient.
6 液压系统选用32＃抗磨液压油。定期检查油箱中液压油的液面应在3／4高度以上，否则应加油达要求。
6. 32 # anti-wear hydraulic oil is selected for hydraulic system. Regularly check that the liquid level of hydraulic oil in the oil tank should be above 3/4 of the height, otherwise fill the oil to meet the requirements.
维护与保养：
Maintenance:
1 新机器经过一段时间的运转之后，应打开护板，检查各紧固件是否有松动现象，并重新紧固。
1 After a period of operation of the new machine, open the guard board, check whether the fasteners are loose, and retighten them.
2 每次使用完毕，要将机器的残胶及灰尘干净，使传送带及机器外表保持清洁，且皮带接口停于台面上，离开胶头20cm以上。
2 After each use, the residual glue and dust of the machine shall be removed to keep the conveyor belt and the machine surface clean, and the belt interface shall stop on the table and be more than 20cm away from the rubber head.
3输送装置两侧主动轮和从动轮轴承每隔3个月应加注一次润滑油脂。
3 The bearing of driving wheel and driven wheel on both sides of the conveyor shall be filled with lubricating grease every 3 months.
4 液压系统用油应每年换一次,并定期检查系统是否有漏油现象。
4 The oil used in the hydraulic system shall be replaced once a year, and the system shall be checked regularly for oil leakage.
5 定期检查电气接线是否有松动及接地的可靠性。 友情提醒：为保证设备的良好运行，应加强设备的日常维护与保养。
5 Regularly check whether the electrical wiring is loose and whether the grounding is reliable. Friendly reminder: In order to ensure the good operation of the equipment, the daily maintenance of the equipment should be strengthened.
以上就是为大家介绍的有关全自动丁基胶涂布机详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://linshi.jncsjx.com
The above is a detailed introduction to the automatic butyl rubber coating machine, and we hope it will be helpful to you. If you have any questions, please contact us. We will provide you with our attitude http://linshi.jncsjx.com