自动涂胶基本过程
Basic process of automatic gluing
1.测宽：次使用或铝框宽度改变后，需要对铝条进行测宽，以便传送时铝框顺利通过胶嘴。
1. Width measurement: after the first use or the width of the aluminum frame is changed, the aluminum strip needs to be measured so that the aluminum frame can pass through the rubber nozzle smoothly during transmission.
2.加热：进入自动状态后，胶嘴和胶盘要行加热，同时传送带转动，以免胶嘴温度升高后将传送带烫坏，温度高于80度以后打胶流程才会起效。
2. Heating: After entering the automatic state, the rubber nozzle and rubber plate shall be heated first, and the conveyor belt shall rotate at the same time, so as to prevent the conveyor belt from being damaged after the temperature of the rubber nozzle rises, and the gluing process will take effect only after the temperature is higher than 80 degrees.
3.传送打胶：当达到设定温度后，手持铝框放在传送带上，当前端打胶光电检测到铝框时，自动涂胶过程开始。打胶光电有信号后，延时一段时间，前压轮下压，压住铝框；前压轮下压后延时一段时间，胶缸前进，胶嘴出胶。开始涂胶后，再延时一段时间，后压轮下压。打胶光电信号消失后，延时一段时间，前压轮抬起，前压轮抬起后，再延时一段时间，胶缸停止前进，同时胶嘴停止涂胶；停止涂胶后，再延时一段时间后，后压轮抬起，铝框一边涂胶完成。
3. Transfer gluing: when the set temperature is reached, the hand-held aluminum frame is placed on the conveyor belt. When the aluminum frame is detected by the current end gluing photoelectric detector, the automatic gluing process starts. After there is a signal from the gluing photoelectric device, delay for a period of time, and press down the front pressing wheel to press the aluminum frame; After the front pressing wheel is pressed down, the rubber cylinder will move forward and the rubber nozzle will discharge. After the gluing is started, delay for a while, and press down the rear roller. After the photoelectric signal of glue application disappears, delay for a period of time, and the front roller lifts. After the front roller lifts, delay for a period of time, and the rubber cylinder stops moving forward, and the rubber nozzle stops applying glue; After stopping the gluing, after a further delay, the rear pressing wheel lifts and the gluing on one side of the aluminum frame is completed.

之后重复传送打胶流程，将铝框剩余三边全部涂上丁基胶，铝框涂胶就全部完成。
After that, repeat the transmission and gluing process. Apply butyl glue to the remaining three sides of the aluminum frame, and the gluing of the aluminum frame will be completed.
因为大多数铝框为方形而少数为圆形，所以在自动中可以进行方形和圆形的切换。当为圆形框涂胶时，中间压轮压住圆框，同时皮带转动，胶嘴出胶，松开脚踏开关该过程停止。
Because most aluminum frames are square and few are round, you can switch between square and round automatically. When applying glue to the round frame, the middle pressing wheel presses the round frame, while the belt rotates, the glue nozzle releases glue, and the process stops when the foot switch is released.
以上就是为大家介绍的有关双组份打胶机详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://linshi.jncsjx.com
The above is a detailed introduction to the two-component sealant dispenser, and we hope it will be helpful to you. If you have any questions, please contact us. We will provide you with our service in the same manner http://linshi.jncsjx.com