很多时候我们在使用中空玻璃打胶机时感觉不顺畅，但是具体还说不出到底是那里出现了问题。这时候就要去找厂家询问、资讯，或者更严重的花钱让售后来维修。今天小编就给大家总结一下，关于中空玻璃双组份打胶机会出现的那些问题现象、问题的因素以及办法。
Sometimes we feel bad when we use the hollow glass gluer, but we can't tell exactly where the problem is. At this time, you have to go to the manufacturer for inquiries, information, or even more serious money for later maintenance. Today I'll give you a summary of the problems, phenomena, factors and solutions of the two-component gluing opportunities for hollow glass.
问题1：在打胶过程中，有时还没有打完就开始以后的动作。
Question 1: In the process of gluing, sometimes the action after the gluing is started before the gluing is finished.
这种情况下是非常不好的，很容易损坏玻璃，那么这种现象出现的原因有以下哪几种呢，我们一起来看一下。
In this case, it is very bad. It is easy to damage the glass. Then what are the reasons for this phenomenon? Let's take a look at it.
出现因素：1）可能由于机头前面的光纤头有东西遮挡，比如（胶之类）。
Appearance factors: 1) may be due to the optical fiber head in front of the nose has something to block, such as (glue, etc.).
2）可能由于光纤头螺母松动或者倾斜。
2) It may be due to loosening or tilting of the nut of the optical fiber head.
3）玻璃的表面有脏东西。
3) There is dirt on the surface of glass.
4）检测距离太小，行走时有波动影响检测。
4) The detection distance is too small and there are fluctuations when walking.
办法：如果遇到上述问题的话，方法很简单；1）清理干净光纤头，就可以。
Solution: If you encounter the above problems, the solution is simple; 1) Clean up the optical fiber head, you can.
2）倾斜或者松动，需要把它固定好，调整好。
2) tilt or loosen, it needs to be fixed and adjusted.
3)玻璃表面的脏东西会影响打胶等等，所以清理干净玻璃表面就可。
3) The dirty things on the glass surface will affect the gluing and so on, so clean the glass surface can be.
4）调整合适的检测距离。
4) Adjust the appropriate detection distance.
问题2.工作过程中总是有些不协调，各个动作之间不协调。
Question 2. There is always some disharmony in the process of work, and each action is not coordinated.
出现因素：1）参数设置有误
Occurrence factors: 1) incorrect parameter setting
2）气动系统配件老化。
2) Aging of pneumatic system accessories.
办法：1）重新设置参数，或者使用原始参数。
Solution: 1) Reset the parameters or use the original parameters.
2）如果是气动系统配件老化的话，就更换一个新的。
2) If the pneumatic system fittings are aging, replace a new one.

问题3、在行走过程或者传送停止时，会出现一些玻璃渣。
Problem 3. Some glass slag will appear during the course of traveling or when the transmission stops.
出现因素：1）胶嘴护套损坏。
Occurrence factors: 1) Rubber nozzle sheath damage.
2）铝槽深度检测探头行走时划到玻璃。
2) Aluminum groove depth detection probe runs into the glass when walking.
3）刮胶板或者挡胶板的前进力量太大。
3) The forward force of the scraper or baffle is too large.
办法：1）很简单，重新换一个护套就可以。
Solution: 1) Simple, just change a new sheath.
2）调整探头的位置，让它在铝槽中间行走。
2) Adjust the position of the probe and let it walk in the middle of the aluminium groove.
3）调节前进气缸的速度到合适。可以避免出现玻璃渣。
3) Adjust the speed of the forward cylinder to a proper level. Glass slag can be avoided.
问题4.电机不稳定，时快时慢。
Problem 4. The motor is unstable, fast and slow.
这个问题也是比较简单的。
This problem is also relatively simple.
问题因素：1）铝槽不直。
Problem factors: 1) Aluminum groove is not straight.
2）导轨不直或者滑动轴承损坏。
2) The guide rail is not straight or the sliding bearing is damaged.
办法：1）铝槽要平直。
Solution: 1) Aluminum groove should be straight.
2）如果损坏或者导轨不直，可以更换。
2) If damaged or the guide rail is not straight, it can be replaced.
以上的精彩内容由双组份打胶机厂家友情提供，更多的精彩内容请继续关注我们：//www.qianyantong-e.com，我们会有更多的精彩内容等你查看！
The above wonderful content is provided by the friendship of the two-component glue maker, more wonderful content please continue to pay attention to us: //www.qianyantong-e.com, we will have more wonderful content waiting for you to see!