如何做好双组份打胶机在使用中的点胶操作
　　How to do well the dispensing operation of two-component dispenser in use
　　1. 固化元件:对于胶水的固化，一般厂家给出了温度曲线。一般在室温下即可固化，在实际应用中应尽量选择较高的温度进行固化，使固化后的胶水达到强度和硬度。
　　1. Curing element: for the curing of glue, the general manufacturer gives the temperature curve. Generally, it can be cured at room temperature. In practical application, it should be cured at a higher temperature as far as possible to make the cured glue reach the strength and hardness.
　　2、泡胶机在泡胶的过程中会影响到产品的质量，所以在涂胶前不能有泡胶。
　　2. The quality of the product will be affected by the foam machine in the process of foam, so there should be no foam before coating.
　　3,真空吸入阀必须安装在配药机,由于真空回吸功能是防止胶水点胶机不是调剂滴泄漏,如果安装工具包可以合理调整真空吸入阀,并进一步可以控制滴泄漏和绘画这两个病例。
　　3. The vacuum suction valve must be installed in the dispensing machine. Because the vacuum suction function is to prevent the glue dispenser from leakage of dispensing drops, if the installation kit can reasonably adjust the vacuum suction valve, and further control the two cases of drip leakage and painting.
　　标准4、针和类别:针标准会影响在调剂的过程中胶粘剂范围和精度,当压力,喷嘴针越大,速度越大,所以要分配的基础上机器生产产品的侵入性的标准锚点胶针,针直径长度保持胶点直径的一半,效果很好。
　　Standard 4, needle and category: needle standard will affect the range and accuracy of adhesive in the process of dispensing. When the pressure and nozzle needle are larger, the speed is larger. Therefore, the invasive standard anchor needle of the product manufactured by the machine on the basis of distribution is required. The diameter length of the needle keeps half of the diameter of the glue point, and the effect is very good.

　　5、点胶量的大小是由点胶机在点胶过程中持续的时间长短决定的，时间越长。
　　5. The size of dispensing volume is determined by the duration of the dispensing machine in the dispensing process, the longer the time.
　　6、在点胶机中一般使用的胶水可能有环氧树脂、速溶胶、硅胶、厌氧胶、UV胶等。
　　6. The glue commonly used in dispensing machine may be epoxy resin, quick sol, silica gel, anaerobic glue, UV glue, etc.
　　7,侵入性压力直接影响流的速度胶水,胶水,胶水更糟的活动变得厚,它需要更大的压力,所以我们应该基于配药机在生产过程中环境温度和侵入性胶胶量的特性来调节压力,胶侵入的压力是通过其内部压力调节阀进行调理。
　　7. The invasive pressure directly affects the speed of flow. The worse activities of glue and glue become thicker. It needs more pressure. Therefore, we should adjust the pressure based on the characteristics of the ambient temperature and the amount of invasive glue in the production process of the dispensing machine. The pressure of glue invasion is regulated by its internal pressure regulating valve.
　　以上双组份打胶机的介绍希望对您有所帮助，我们的产品质量好，合理，真诚欢迎您选购，我们竭诚为您服务。
　　The introduction of the above two-component dispenser is hoped to be helpful to you. Our products are of good quality and reasonable price. We sincerely welcome you to buy and we will serve you wholeheartedly.